West Elm Inspired Tripod Floor Lamp {Knock Off Decor Series}

Share this with your friends!Share on Facebook14Pin on Pinterest2,484Share on Google+45Tweet about this on Twitter9Email this to someoneShare on StumbleUpon1Buffer this page

 Hi friends!  I hope you are smack dab in the middle of a fantastic weekend!  I’m really excited to share my West Elm knock off lamp with you today!

We have been busy DIYers around here, which has paid off because today is the first day of my Knock Off Decor Series and I am so excited about it!  One, because it is my first ever series, but also because all of those awkward moments taking photos of the lovely things I see in stores, only to get the stink eye from the people working there will finally pay off!  Do you ever do that?  I almost always enter a home decor store ready to  shop for take pictures of what I can recreate.

West Elm is one of my favorite stores and when I was browsing around in there a few months ago, I fell in love with their wood tripod floor lamp.  Then I immediately fell out of love with it because it was $250 bucks.  Then I fell in love with the idea of recreating my own very similar one.  And so my DIY West Elm knockoff  version was born and I’m going to show you how we made it for just under 40 bucks!  Isn’t it pretty?

West Elm Knockoff Tripod Floor Lamp

I think I came pretty close to the one that inspired it all don’t you?

West Elm Knock Off Wood Tripod Floor Lamp

So are you ready to make your own?  If you can make a few cuts with a saw and do a little bit of drilling, you can do this project.  I’ll walk you through it and give you some little tips along the way so you can avoid some of my mistakes.

Supply list:

 

How to make a West Elm inspired tripod floor lamp

  • Three 3/4 inch square, 6 ft. long pieces of wood for the legs of the lamp.  Get wood that looks nice and smooth especially if you are going to leave it natural like I did.
  • 1/4 inch metal cable clips to attach the metal ring at the bottom.  (I found these at the hardware store next to the cable wire.)
  • a lamp kit (Amazon affiliate link)
  • 6 inch brass nipples (found right next to the lamp kit)
  • a pack of nuts and washers for lamp parts (also right next to the lamp kit)
  • a 4 inch piece of scrap wood that is about 1 1/2- 2 inches thick to hold the top of the legs together and to hold your light.  I used MDF board from the trash can in the back of the home depot.)
  • a can of spray paint to paint your metal pieces and the cord.  I used Krylon Gold Metallic spray paint (Amazon affiliate link)
  • 3 screws to attach the legs
  • a lamp shade and bulb
  • the top metal ring of a 16ish inch lamp shade.  It needs to be one with 3 prongs like the one in the photo above.  (I found mine at the Salvation Army for 3 dollars and ripped out the top ring.)

How to build a Wood Tripod Floor Lamp:

Step 1: Spray paint the top ring of the lamp shade that you ripped apart, 3 cable clips and screws that go with them, and your cord in the color of your choice.

Step 2: Cut each of your wood legs to 55 inches at a 5° angle at the top and bottom making sure that the surfaces of the ends are parallel.

DIY Tripod Floor Lamp West Elm Knockoff

Step 3: Decide the placement of your bottom ring and attach the cable clips.

Have a buddy, hold up your cut legs in the position that they will be on your finished lamp while you hold the ring in place toward the bottom and mark where the cable clips will go.

You want to make sure that your lamp will be steady so be sure that the legs are not too close together.  My ring was 15 inches and the ring ended up being 15 inches from the bottom of the legs.  If your ring is a little bit smaller, you will need to move it up to keep the tripod wide enough.

Once you have marked where your ring will go, attach the cable clips to the inside side of each leg.

DIY Tripod Floor Lamp West Elm Knockoff

This part gave us a bit of trouble but here is what finally worked.

Step 4: Create a triangle to hold everything together.

Cut a triangle out of your scrap piece of wood that is 3 1/2 inches on each side.  Then, mark 3/4 of an inch in from each point on all sides and cut each point off at a 10 ° angle.

Pre drill a hole for the nipple of the light kit in the center of your triangle too. (We didn’t do this and realized that it would be easier to drill this hole before attaching the legs…whoops!)

Step 5:  Attach the legs.

It is really important to pre drill your holes and go slow because you are working with small pieces of wood and you don’t want them to split.

So, pre drill holes (at a little bit of an angle) in each side of your cut triangle and each outside edge at the top end of your legs.  Then, attach each leg with a screw, going slowly so you don’t split the wood.

pinching brackets

Step 6: Attach your bottom ring.

Place your bottom ring into the cable clips and press the clips in with your finger to hold them in place.

pinching brackets

Step 7:  Assemble the light kit.

Follow the instructions on the package of the light kit to attach it to your tripod lamp.  I had the bottom of the 6 inch nipple pretty far down to add detail in the finished product.  It will depend on your lamp shade, but you want the lamp shade to just cover the wood triangle part at the top.

Step 8: (optional) Stain your legs.

I rubbed a coat of teak oil on my legs just to bring out the natural color of the wood a little bit.  I really liked the natural color though so I didn’t stain them.  Plus I like the contrast of the wood tones when it is next to the Rustic Floating Shelves that we built.

Step 9: Add a shade and you are done!

I recovered a large lamp shade that I found at a thrift store for $5.  It had a textured fabric on it originally, but I was still able to make it work and I’ll be showing you how I did it later this week.

West Elm Knockoff Wood Tripod Floorlamp

So here she is in all her beauty!  I love the simple details that the metal brings and may I just say this tripod lamp looks perfect against the subtle pattern of the DIY Sharpie Wallpaper!

West Elm Knockoff Wood Tripod Floorlamp

So what do you think?  Did I get it pretty close to the inspiration?

This is just the beginning of a six week series on knock off decor projects so be sure to subscribe to my email list (daily or weekly) so you don’t miss all of the fun inspiration!

Have a great rest of your Sunday!

Sharing at Remodelaholic and Home Stories A to Z
signature-2014Linking up at THESE GREAT PARTIES and Remodelahoic and Home Stories A to Z
Share this with your friends!Share on Facebook14Pin on Pinterest2,484Share on Google+45Tweet about this on Twitter9Email this to someoneShare on StumbleUpon1Buffer this page
call to action

Comments

  1. says

    I love it, you did a great job! I actually have a real tripod that I picked up at a thrift store for $5 that I’ve been planning on making into a lamp, your awesome tutorial will help me I think!

    Tania
    Tania recently posted…Treasure Trove TuesdayMy Profile

Trackbacks

Leave a Reply

Your email address will not be published. Required fields are marked *

CommentLuv badge